The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

The mxl 0.08" pitch is fine for moving the weight of a gantry that contains a 40 watt laser tube and optics. I would not advise this timing belt for CNC applications that need to move heavy items such as spindles, routers, and heavier structures that are required to move these spindles and routers around.

The mxl 0.08" pitch timing belt is also great for 3d printers.

Click the link to add information to this solution:
Originally bought the Blacktooth Laser kit, but the upgraded laser tube size and needed a larger casing. With that I need to upgrade the belts to a 36" run. Can you advise whether the mxl.08" timing belt is sufficent or do I need the .2"in.

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

Drivers will have terminals with labels that represent a pulse, clock or step, and for direction. Look at the following to determine which terminal is used for what purpose.

Step- = CP- = P-
Step+ = CP+ = P+
Dir - = CW- = D-
Dir+ = CW+ = D+

Click the link to add information to this solution:
Hi, I have one of your mach3 controller boards and have followed the tutorial videos but my motor drivers do not have p+ p- d+ d- I only have sted, dir, en and +5v

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?

Sure, email me at customerservice@buildyourcnc.com and I will send you a replacement for a minimal fee. I now use HDPE for that part. The HDPE holds up much better.

Click the link to add information to this solution:
I have a Blackfoot 4x4 v2 chain drive. my Y plate is broken . do you sell just the Y plate or can I buy just the Y plate spec plan? I love this machine Its great. my name is Jeff Krug I bought the complete package and electronics from you guys. thanks

The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

What is the model number of the laser controller?

Additional Information:
Hey - the model number on the laser controller is
AWC708C
S/N:708014243

Additional Information:
Do you need any additional information here? I really want to get going on it this weekend!

Additional Information:
Sorry about that. If you are referring to the CN1 and CN2 connector, I don't believe it is needed if it didn't come with the connector. The components that we send to the customer is the same package that is sent from the manufacturer of the product. I would try connecting it to the CN1 connector of both units and test the interface (control panel).

Additional Information:
The manual for the AWC 708 shows the two ports CN1 and CN2 connected, but that may just be for thorough documentation if the CN2 is needed for some reason. Do you have a copy of the manual or know where to find it? If not, I will put the document link here.

Click the link to add information to this solution:
my 40w blacktooth laser kit with laser control unit only came with one controller connector, but the unit has two controller ports. Should I have two wires or do I just use controller port number one?

As shown in the instructions the laser tube that was used was a different model which had the metal end, compared to our full glass tube models we currently ship with the machines.
So there is no difference besides appearance between the two tubes.
The focus lens should be placed in the laser nozzle assembly and not on the laser tube itself.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I bought a blacktooth laser from you about a year ago.. I am finally getting around to installing the laser tube and I noticed that my tube does't have the metal end on it like all the pictures I've seen. is this a focus lense and can I purchase one?

Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks

If you would like to replace a router that outputs a relatively low HP (horse power) such as the Bosch PR20EVSK or Dewalt 611, both having about 1-1.25 HP, the 1.5kW spindle would have more than enough power and will also provide constant torque where the routers are unable to achieve. The 1.5kW spindle outputs 2 HP and is water cooled to keep the dust out of the air!

Click the link to add information to this solution:
I'm looking to upgrade my X-Carve with one of your vfd spindles, can you reccomend which one to use to replace the dewalt 611 router?

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

The greenBull CNC machine kit can cut as thick as a material as you desire depending on the reach of the end mill that you provide the machine, if it is a straight vertical. The reason for this is that each pass is incremental (multiple passes at a certain depth per pass). For instance, if you need to cut a 2 inch thick piece of wood, you can make, say 3/4" passes until the target depth of 2 inches is met.

The depth per pass, feedrate and RPM will be determined by the material: wood, plastic, metal and will also be determined by the end mill that is used for that material. Selecting the appropriate end mill is very important. Feedrate and RPM is important to make sure the end mill is as cool as it can be during the cutting process.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How thick can the Greenbull cut and what kind of material? Wood, plastic, steel? I was also wondering if there is one anywhere in Nevada, Idaho or Utah that I could possibly see in action. Thanks

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

Pokeys57CNC product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia