You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?

Headsets have been tested by the manufacturers and meet the current ANSI/IEEE standards for RF safety, the same standards that the Federal Communications Commission enforces under the Telecommunications Act of 1996. These standards place limits on the specific absorption rate (SAR) of radiofrequency (RF) energy in the body. Recent inflamatory articles in British press were not substantiated by testing in ISO-accredited testing facilities at Motorola. Manufacturers of cellular phones are required under FCC regulations to assure that their products meet the SAR limits on both hand-held and hands-free units. Further information may be available from the FDA or from the FCC. Ron Petersen, Lucent C.K. Chou, Motorola

Click the link to add information to this solution:
HAVE THERE BEEN ANY STUDIES OF POSSIBLE RADIATION DANGER FROM HEADSETS USED WITH HANDSETS CORDED TELEPHONES? I A TELEPHONE BATTERY-POWERED HANDSET. THIS HANDSET HAS JACK FOR HEADSET, SO YOU CAN WALK AROUND THE HOUSE AND YARD ON YOUR BELT WHILE TALK INTO HEADSET. EITHER OR HEADSET GIVING OFF RADIATION, LIKE CELLULAR PHONE? DANGEROUS AMOUNT RADIATION?

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

Our spindle should work fine with your Delta VFD-M 220v. Spindles that match a VFD are specific to the coil windings. The bearings, shaft and other mechanical components that make up the spindle may be different, but that should not matter.

Click the link to add information to this solution:
I have a GMT 2.2kw water cooled spindle that sounds like the bearings are going out and want to know if your spindle (https://buildyourcnc.com/Item/spindle-inverter-2!2kw-spindle-novfd) is comparable for a swap. The drive is a Delta VFD-M 220v.

We did give out the plans for our machines many moons ago, but a few winters back we had to cease this practice as the night was young and full of terrors. Unfortunately we no longer offer the .dxf files or g-code files for any of our CNC machines.

To build a roll cart for your blueChick, check out the similar cart we created for our blackTooth laser. (https://buildyourcnc.com/tutorials/Tutorial-sketchup-fabrication-fabricate-cad-cam-dxf).

Click the link to add information to this solution:
Many moons ago (when we were all a lot younger) you offered an export plan that consisted of various combinations of hardware/electronics and SketchUp of the CNC machine. Do you still offer SketchUp of your projects? I bought the new BlueChick and would like to build a roll-around cart for it. I might also wish to make modifications so a SketchUp would be most helpful.

We will contact you with a list of options.

Click the link to add information to this solution:
I would like to upgrade my older engraver to usb or parallel port i want to build as much of it as possible to cut down on expense. The name of the engraver is New Hermes vanguard 4000 the specs can be found on the internet. Looking to purchase parts today please contact me at 937-262-8446 or email me at isaacjcrawford@sbcglobal.net with the information and part numbers thanks.

It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Additional Information:
It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Click the link to add information to this solution:
[59] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

Considering enlarging the machine, might have its down sides do to the structural integrity of the scratch build machine. Primarily by making the width longer it will start to sag in the center, which will lead to having to redesign the gantry to be more structurally rigid to support the added length. Which then will increase the weight and height of your gantry to support the add size, which will always end up to creating a larger CNC.

We usually do not recommend modifying the scratch build CNC, due to the very limited capabilities, and the structural design of the scratch build. We also do not recommend using longer than 48" ACME screw/leadscrew due to the increasing chance of warping and bending in the ACME screws/leadscrew in the given length.
We do recommend modifying the CNC machines we sell to accommodate the added requests that some of our customers desire, but you will be limited to the width of the gantry with our machines.

Click the link to add information to this solution:
I've read your book and I'm looking to purchase the hardware kit with DVD as well as an electronics kit. I would like my machine to have a working area of at least 24" wide by 48" long. Can I just make the bed (and gantry) wider to accommodate larger priceslike 30"x60"? If so what electronics kit would you recommend?

The motor with that model number is here: https://buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

Click the link to add information to this solution:
In looking for a stepper motor amongst old parts in my lab, I found one with a sticker that says buildyourowncnc.com and PN SM60HT86-2008BF U2 on it. I found a Q&A on your website that says it's a NEMA 24 motor with 425 oz/in holding torque. I was wondering if you were able to confirm this? Any specs sheets and details of the motor would be much appreciated

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
Limit switches for axis. The print shows that you can wire the limits either n.o. or n.c. so if this is correct I would need to tell the board in the software how to look at these limits, I'm either going to get an input or loose an input depend on how i wire it.

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

Dealing with a 4' x 12' machine, our blackFoot kit will be your best option. Since our machines are only limited to the width but not length wise, you can add however much extra rail and roller chain to accommodate your extended length. Now adding our 4th axis kit (https://www.buildyourcnc.com/item/axes-4th) will be needed for your 4th axis (unless custom design is required).

These items will be the best requirements to build a 4' x 12' 4th axis machine.
Machine (either parallel/USB BoB): https://www.buildyourcnc.com/blackFoot48v40.aspx
4th axis: https://www.buildyourcnc.com/item/axes-4th

Click the link to add information to this solution:
I am looking to set up a long table, 4 x 12 foot I would need to cut wood of modest density less than 1 inch thick, and I would also need to bevel some of the cuts, so I think this is a four axis unit. Which of your kits plus upgrades would make sense? I am very capable of assembly of a bunch of boxes full of parts.

https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.

On "our" VFDs, we advise that the R connect to black (live), T connect to white (neutral) and green to E or earth. We are not professional electricians, so we also recommend that you seek the advice of a professional electrician. Some VFDs are made to work on 3 phase power and this configuration may not work with these VFDs.

Click the link to add information to this solution:
On your diagram it says to connect the power to the VFD in port L1, L2 and PE. On the VFD I have there is no L1 or L2. Which ports do I connect my input power to? There is only a P+, P-, R, S, T, U, V, W, and PE. What do I do?

Yes, you can use the onboard relays on the pokeys57CNC controller to trigger the plasma torch.

Click the link to add information to this solution:
I want to trigger a plasma torch with the Pokeys57CNC that I bought from you. I am connecting a Proma THC following your basic instructions for the Plasma sense But I don't know what I would use to trigger the torch. I watched the video on lazer engraver. Can I use the same for triggering a plasma torch?