The THC and the triggering of the plasma are actually two different functions of a controller. To trigger a plasma cutter, you can use one of the outputs of the Mach3 USB controller (out 1, 2, 3, or 4). That output can be connected to a relay that connects to the two wires that will trigger the plasma.

This video will show how this is done:

Click the link to add information to this solution:
[575] How can I wire/ configure for a plasma cutter without THC? Plasma cutter has a cnc port, where when you short two of the pins, it activates the cutter. Just looking to see how to make that short when pressing f5 in Mach3.

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?

The term cGy (centigray) is a unit of absorbed dose of ionizing radiation such as x rays or gamma rays. Cell phones do not emit ionizing radiation. They emit nonionizing radiation, namely radiofrequency (RF) energy. Absorption of nonionizing radiation in the body is measured in terms of the specific absorption rate (SAR) in units of watts per kilogram. Both ionizing and nonionizing radiation are forms of electromagnetic energy. The difference is that ionizing radiation has sufficient energy per photon to cause ionization of molecules. Nonionizing radiation does not. It is the ionizing effect of ionizing radiation that has been linked to increased risk of cancer. For more information on cell phones and health check out a Medical College of Wisconsin website. For more information on ionizing versus nonionizing radiation check out a University of Michigan website. Gary Zeman, ScD, CHP Lawrence Berkeley National Laboratory

Click the link to add information to this solution:
MY QUESTION THAT KNOW CANCER CAN BE CAUSED WHEN OUR BODY EXPOSED TO DOSES OF 50 CGY OR HIGHER. WHAT DOES STAND FOR? DO EMIT?

Yes, we can supply the parts for a machine that will turn pipes so they can be cut as they are turning. Are you intending the machine to cut using a milling process, or a plasma process?

Click the link to add information to this solution:
I want to cut the ends of steel pipes circularly as preparation for welding by plasma cutter , can you supply small machine?

We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

According to the supplier of the 2.2 kW spindle, the safest operating speed for the spindle is 6000 RPM. The supplier also stated that theoretically, the spindle can operate from 0 to 24,000 RPM. I am continuing a dialog with the supplier to delve deeper into understanding the configurations and ramifications of such configurations for operations outside of the safe boundaries into the "theoretical" ranges.

Additional Information:
20

Click the link to add information to this solution:
I would like to know what the lowest rpm that can be acheived with the 2.2kw spindle and inverter and still have enough torque to drill

Yes, you can use the onboard relays on the pokeys57CNC controller to trigger the plasma torch.

Click the link to add information to this solution:
I want to trigger a plasma torch with the Pokeys57CNC that I bought from you. I am connecting a Proma THC following your basic instructions for the Plasma sense But I don't know what I would use to trigger the torch. I watched the video on lazer engraver. Can I use the same for triggering a plasma torch?

Yes the CNC will do 3D wood carving and we can ship to Mexico. email sales@buildyourcnc.com for more information.

Click the link to add information to this solution:
I have a New Hermes Vanguard 4000. It has an IS controler. I know nothing about these machines. What can I do to make it usable?

The Mach3 USB Interface Board is designed to handle an output current of 50mA. These outputs are generally not suitable for heavy loads like Spindle Governor Relays (SGRs)​​. Given that your SGR pulls 2.6 Amps, it exceeds the capacity of the Mach3 USB Interface Board's output. Therefore, directly switching the SGR using the Mach3 USB Interface Board is not advisable. Instead, using your existing C36 rev1.1 board as an intermediary would be the recommended approach. This board can handle higher currents and will act as a buffer, protecting the Mach3 USB Interface Board from being overwhelmed by the higher current demand of your SGR.

Click the link to add information to this solution:
[575] How many Amps can the output handle? My SGR pulls 2.6 Amps so I need to know if the output can handle that much.

If you would like to add a laser to a plasma table, you will need the following parts:

Laser tube at 40 watts:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Tube-CO2-40Watt

Mirror mounts (this will depend on the way you mount the laser tube):
https://www.buildyourcnc.com/item/Laser-Component-Mirror-Mount-20mm

Mirrors for the mirror mounts:
https://www.buildyourcnc.com/Item/Laser-component-20mm-mirror-25mm

Laser Tube Power Supply:
https://www.buildyourcnc.com/item/Laser-Component-Power-Supply-CO2-40W

Laser Focus Lens:
https://www.buildyourcnc.com/item/laser-component-20mm-lens-2-inch-50!80mm

Mirror and Lens Mount and Nozzle:
https://www.buildyourcnc.com/item/Laser-Component-Nozzle-20mm-lens-mirror

High Tension Extension Cable:
https://www.buildyourcnc.com/item/Laser-component-Power-Supply-High-Tension-extension-wire

Laser Control System:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

Screw Posts (to connect the high tension and return wire to the laser tube, highly recommended as the leads on the laser tube are fragile):
https://www.buildyourcnc.com/item/laser-component-newbiehack-connectors-screw-terminal-binding-post

Safety Eyewear for CO2 laser wavelength:
https://www.buildyourcnc.com/item/laser-components-goggles-safety-tinted

Click the link to add information to this solution:
I have an Eagle Plasma table and I want to add a 40 laser. Can you supply me a list of what I need to make this happen.

You can test the power supply, but you will need to take extra special care since the voltage on the high tension line can be lethal. Go to this instructable to see all the step on testing the power supply:

http://www.instructables.com/id/How-to-test-and-set-a-Chinese-China-made-CO2-Laser/?ALLSTEPS

Additional Information:

Click the link to add information to this solution:
I am building the Blacktooth laser cutter. What is the safest and most accurate way to test the output of the laser power supply WITHOUT connecting the laser tube? Can I use a standard multimeter and measure the voltage output of the laser power supply?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

The best choice would be a type K thermocouple.

Click the link to add information to this solution:
I have the hot end listed on your site here :http://buildyourcnc.com/item/3D-Printer-Component-extruder#prettyPhoto what thermocouple or thermistor do I need for the hot end? it is not clear my original order was the email jeremy.adair@compassauto.net. please let me know what I need to buy. thanks.

We are working on a keypad that will connect to the USB interface. It is possible to create a quick keypad using perf-board and some push buttons. All you need to do is connect one side of the switch to the pin of the axis and direction and the other side of the push button to the 5v pin. The datasheet shows the pinout of the jog connector.

Additional Information:
I had found the pins to wire in a job connector. My question is, what sort of connector do I look for (on Amazon for example) that will work for each 2 pin pair? I suspect they are the same as the connector for power and reset on my computer's motherboard, but I have no idea what to look for (what to buy).
thanks.

Additional Information:
20

Click the link to add information to this solution:
I need to find a connector(s) to wire a pushbutton array to the USB board I purchased. Do you sell such a connector. Can you tell me what to look for?/What such a connector is called?

You can call us, send an email, or pose the specific question on this customer service live that pertains to the issue that you are having.

Click the link to add information to this solution:
Im having software setup problems with my backtooth (mach3) and i seem not to find a solution in the forum. what can i do?

If you are referring to the polabs website that presents in another language, on that site, there is a button on the top right that says "options" with a down arrow. Click that and click turn off translation.

Click the link to add information to this solution:
[659] When clicking the manual link, it wont let me switch to the American version. How do I get that link?