Currently the only options available for our computer systems, are for our machines which included all the motors and drivers. If you would like to talk about a custom order, please email (customerservice@buildyourcnc.com).

Click the link to add information to this solution:
Do you sell the computer system only ? My Dell has given up the ghost. I may want to buy the PC, Power and case. I have everything else.

See initial question.

Additional Information:
Initial question is: https://www.buildyourcnc.com/FAQ/14009

Click the link to add information to this solution:
Follow up to the last question. I can just make a couple new pieces of acrylic but I just wanted to know if you had any other ideas. Thank you.

Call again. Most likely, one of my employees were on the line with another customer at the time you called.

Click the link to add information to this solution:
I am interested in order the redleaf system you talked about for my machine, tried calling and mail box is full, no answer. How do I contact you?

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Hello there, I am a beginner in trying to control a stepper with a pc, you can sell me a kit to control my motor from the pc. I already have a motor, driver, and power supply

Yes, if you wish to get help with a product that was not purchased at buildyourcnc.com, you can go to this link and purchase a token:
https://www.buildyourcnc.com/item/sub-assemblies-Technical-support-token

Click the link to add information to this solution:
[541] I need some help, can I pay you for your time? I have a old Golden Laser has 2 co2 lasers 80 watts each, trying to put a new Ruida 6445G contorller in it.

Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

Click the link to add information to this solution:
I am building a machine that requires 2 steppers to drive the Y axis, can you make me a redleaf system using the 651oz steppers that will work for me?

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

John Parent,

We are currently waiting for rails to come in as they are out of stock. We appreciate your patience. Please email customerservice@buildyourcnc.com and let us know if there is anything we can do.

Click the link to add information to this solution:
hi, i ordered a bunch of stuff from you, the payment went through, it's been 3 weeks, any word on shipping date, I ordered 6 linear rails with block and some sprockets

To install the USB breakout board, there will be no driver to install nor any pop-up will be viewed in your windows task-bar, except only to notify that a USB device has been connected.

If you have planet-cnc installed it should automatically ask for a license number, which if you don't have you will continue without entering any numbers. Please read carefully since there is a pop-up that can erase the entire firmware on your board, and you will basically have a dead board.

Please email customerservice@buildyourcnc.com for further assitance.

Additional Information:
For Windows 8.1 you need to follow special driver installation steps. Download Planet-cnc software MANUAL and scroll down to that paragraph (without it you will not be able to install and use your board).

Click the link to add information to this solution:
I trying to setup your USB Controller card. The planetcnc does not load the card, no driver for usb card. Using windows 8.1.

That video was hosted by Metacafe and I just went to the permalink for the video, but no video. Metacafe failed me on this one. I will look for my raw video (which will take a bit of time) and re-post it to youtube.

If there are specific questions; please post them here and I will help you along the way. As these questions are asked and answered, they help others as well in the future.

Click the link to add information to this solution:
"Step 34 - Software Toolchain Part 1 - Mach 3 Installation" Video is missing. Do you have? Am trying to install Mach3, need someone to hold my hand a bit here :-)

The Mach3 USB controller only works with Mach3. We have a controller that works with Mach3 and Mach4 called pokeys57CNC controller.
Here is a link to that controller:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
Hi Do you know if your Mach3 interface board works with any of other of the current CAM programs such as MACH4?

The Mach3 USB controller only works with Mach3. We have a controller that works with Mach3 and Mach4 called pokeys57CNC controller.
Here is a link to that controller:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
Hi Do you know if your Mach3 interface board works with any of other of the current CAM programs such as MACH4?

Once your place an order you should receive an confirmation email automatically. If you did not receive it please check if you entered your email address correctly or if it may have gone to a junk/spam folder. Generally with certain items we specify a lead time and once orders are ready to ship you will be automatically notified with an shipment notification email, assuming your email address was correctly entered. If you have any questions pertaining to orders please contact sales@buildyourcnc.com

Click the link to add information to this solution:
I ordered a WhiteAnt on Dec 5 (saturday). I have never received an order acknowledgement nor a shipping date, but my credit card has been charged. I don't think that is usual. Can you provide an update, please?

Did you watch the videos on the product page?
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am trying to connect my pockeys57cnc usb controller to my mach 3 software. I am totally lost on how to configure it all. Any help?

When you power up your VFD, you can go into the programming mode by pressing the program button. You can press the up and down arrows to move through the parameters. Press the set button to go into the parameter to see the value of that parameter. If you want to make changes to that parameter, change the value with the up and down arrows until the desired value is shown, and press the set button to accept the changes.

Click the link to add information to this solution:
I AM HAVING TROUBLES FINDING THE PD PROGRAM, HAVE BUT IT DOESN'T SHOW EVERYTHING NEED TO PROGRAM MY VFD. ANY HELP WILL BE APPRECIATED...

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

It looks like my integration with stamps.com is having issues. I am looking at the issue now.

Click the link to add information to this solution:
For some reason your system via USPS will not allow my address? It is the same one you have shipped to in the past. Jerrold Stevens 1684 NW Bonney Dr Corvallis Or, 97330-9159 US 503 374 5680

We already have a system that meets those needs:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You can find that machine on the home page. It's the first machine on the page and all you need to do i click on the "Add A Laser" button at the top left of the image.

Click the link to add information to this solution:
Good day to you! We haven't communicated in quite some time! I am still wanting to pursue a 4 x 8 CNC spindle and 80kw laser system! Please respond so we can put this together!